Faux-Stiks wall decals
December 2, 2006

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Last Updated

Stik-N-Paint Logos Instructions

I decided to show you step by step just how easy it is to paint a great looking logo or stencil with our Stik-N-Paint Logos. Before we get started I think you should know I don't actually stencil, I paint all of my stencils with a smooth foam roller. I like the images to look hand painted..

Step 1.

 

 

 

 

 

 

 

 

Before you begin, lay your stencil face up and apply pressure all over to ensure the tape is secure.

 

2.

 

 

 

 

 

 

Flip the stencil over and remove the backing. Pull straight back on the lining very slowly. If you notice a piece of the stencil sticking to the liner, gently push the liner forward and apply pressure, then proceed to remove the remainder of the liner.

3.

 

 

 

 

 

 

Place the stencil on the wall and apply pressure to the entire front of stencil to ensure every piece is applied to the wall.

4.

 

 

 


Begin to remove the application tape from the front. Slowly pull straight back close to the stencil. If a piece of stencil starts to stick to the tape gently push it back down and continue to remove the tape.

5.

 

 

 

 

 

 


To demonstrate just how easy our stencils are I will paint our new stencil with a white shirt, a roller, and one hand behind my back.

6.

 

 

 

 

 

7.

 

 

 

 

 

 

.

8.

 

 

 

 

 

 

 

9.

 

 

 

 

 

 

 

 

 

10.

 

 

 

 

 

 

 

 

TRADITIONAL STENCILING INSTRUCTIONS

Supplies Needed

Stencils
Repositioning stenciling adhesive
(This allows you to move the stencil and stencil without using tape.)
Paper towels
Paint: water based acrylic paint or oil base: (Paint Creams or Paintstiks)
Stencil brushes (one for each color)
Smooth White Foam roller (if you prefer to roll the letters, this gives it the smooth finish shown in the photos)
Painters tape

Preparation

Spray the back of the stencil pieces allow to dry (refer to back of can, usually 5 minutes)
Center stencils on wall
Line stencils pieces up using the Registration marks on the stencils (x's on the top and bottom of the stencils near the end of stencil) place tape behind registration marks and mark, line up the next stencil piece using the marks on the tape.
Cover areas you are not going to paint with the first color with tape.
(You should not need to tape the stencil to the wall if you are using stenciling adhesive, however, you may want to put a couple of pieces just in case)
To make sure stencils are straight try taping a yardstick to the wall ,using a level to make sure it is straight, then line the top or bottom of your stencil to the yard stick.

Stenciling

There are a few different stenciling methods one could use, the key is to layer very small amounts of color at a time to build the color depth you desire. Applying too much paint may bleed under the stencil with undesirable results.

Using the smooth roller

Roll roller in paint rolling off excess in pan to make sure the roller is not over-loaded, roll paint roller onto paper towel or paper bags until most of paint is off the roller. (If you have too much paint it may go under the stencil, it is better to go back over it when it is dry to the touch rather than put too much on. This is recommended if you want to achieve gives a very smooth hand painted look and it is so quick and easy.
*** For best results you will need to roll 2 -4 coats of paint on for a truly smooth hand painted look. The first coat or 2 will look spotty because your roller is dryer. You should wait until the paint is dry to the touch before applying the next coat. The longer you wait the better your results will be. If you roll the next coat on too soon it will take off some of the paint.

Dry Brush Method

Pour a small amount of paint onto a paper plate.
Dip the end of your stenciling brush into the paint, wetting just the tips of the bristles.
Swirl the brush into a stack of paper towels with a circular motion to remove excess paint and ensure the brush is loaded properly
Work your stenciling brush from the outside of the cutout into the center using a swirling motion, allowing the center to remain lighter.
Use a separate brush for each color, and be sure to select brushes appropriate for the opening.
***If you are stenciling a large area and using different brushes, place a damp paper towel in a plastic bag or in the bottom of a cup to place your brushes in. This will help to keep them from drying out.

Stippling

Stippling is another dry-brush technique which uses a firm tapping motion rather than a circular motion. This technique works well on textured or rough walls to provide a clearer consistent print. It can be used on smooth walls if you are looking for a more textured look. If you use this technique, you may want to load your brush heavier than with swirling.

Cleaning Stencils

To clean stencils, use warm, soapy water and kitchen pad. Simple green works very well also. The Stencils are much easier to clean if done immediately after stenciling. Be careful not to bend pieces of stencil. If you used an adhesive, paint thinner will remove the adhesive.

Storing your stencil

We have provided hanging holes in each stencil to easily hang the stencil for future use. You can also store the stencil flat, do not fold stencil.

Our stencils are for non-commercial home use only. Federal trademark laws prohibit the use of this product on other products for re-sale without approval from their respective Universities.

Return to Store.

 

Roll your roller over paper towels to remove most of the paint.
This is just about right. As you can see there is very little paint left on the roller.
Begin to roll your paint on with even pressure.
Notice my left hand is still behind my back.
This is one coat. Notice one coat of paint does not look very good. Don't worry, it will look great when we are done. Let this dry to the touch and apply your second coat.
Total paint time for first coat, about 1 1/2 minutes.
This is 2 coats of paint. Not bad but he will look better with one more. I only waited 5-10 minutes between coats since I was using acrylic paint. Time so far about 7 minutes.
I finished the 3rd coat. Now I am removing the stencil from the top down.
You will need to peel off the small pieces separately. Use a push pin if necessary to lift the piece from the wall without harming the new paint.
Final painting after 3 coats of paint. Total paint time including wait time between coats, approx. 12 minutes.

Here I am with the finished wall and my shirt is still white!

I also use a roller with my traditional stencils, but if you prefer using a stencil brush, instructions are included below.

Return to Store.

 

Next you will need a small smooth foam roller and a paint tray.

Roll your roller in the paint.

First you will need your paint. You can use latex paint or you can use acryic paint. You need very little paint for these stencils. The bottle shown is actually way more than I need, I could simply use a 2 oz. bottle of black acrylic paint and I would be fine. Cost for 2 oz. less than $1.00.